Journal article · 1991 · Open access

CHARACTERIZATION OF DIAMOND-LIKE CARBON THIN FILMS DEPOSITED BY FACING TARGETS SPUTTERING OF GLASS-LIKE CARBON

Atsushi Suzuki, Y. Hoshi, Tsutomu Isobe, Jack H. JUDY

Journal of the Magnetics Society of Japan, 15(S_2_PMRC_91), S2_751–756 · Published 1 January 1991 · DOI 10.3379/jmsjmag.15.s2_751

Free PDFView at the publisherCite this paper

In brief

“CHARACTERIZATION OF DIAMOND-LIKE CARBON THIN FILMS DEPOSITED BY FACING TARGETS SPUTTERING OF GLASS-LIKE CARBON” is a 1991 journal article by Atsushi Suzuki and 3 co-authors, published in Journal of the Magnetics Society of Japan. OpenAlex counts 1 citations as of 16 November 2026. It is open access: the full text is free to read at Journal of the Magnetics Society of Japan.

Citations
1
References
3
Authors
4

Abstract

In this paper we have attempted to clarify the effect of the kinetic energy of the sputtered particles on the formation of diamond-like carbon thin films using a Facing Target Sputtering System(FTS) which allows deposition of films at a very low gas pressure such as 0.2mTorr. Glass-like carbon is a kind of amorphous carbon which has very small crystallites and its structure is very uniform compare to graphite. Therefore, we have also tried to evaluate the potential of glass-like carbon as sputtering targets. The optical properties of the carbon films were measured with an optical ellipsometer. The structure of the carbon films were evaluated from Raman spectroscopy. The electrical resistivity was measured using a four point probe technique. The mechanical properties were measured with a microscratch tester. The above experimental results indicate that the structure of FTS deposited carbon films changes from less amorphous to diamond-like as the argon gas pressure is decreased and their adhesion and uniformity was significantly improved. FTS carbon films about 300Å thick were also deposited on textured Co-Cr-Ta/Cr/Ni-P/Al 3.5"rigid disks for the characterization as wear resistant overcoats. The friction of the carbon films were measured using a computer-controlled constant linear velocity drag tester with a thin film head slider. The results show that the friction coefficient decreased from 0.95 to 0.45 as the argon gas pressure was decreased from 10mTorr to 0.2mTorr. Carbon films deposited at 0.2mTorr Ar pressure show significantly lower friction and much greater durability than those deposited at 10mTorr Ar pressure. These results support the conclusion that FTS deposited carbon films have excellent potential as high-durability overcoats.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Suzuki, A., Hoshi, Y., Isobe, T., & JUDY, J. H. (1991). CHARACTERIZATION OF DIAMOND-LIKE CARBON THIN FILMS DEPOSITED BY FACING TARGETS SPUTTERING OF GLASS-LIKE CARBON. Journal of the Magnetics Society of Japan, 15(S_2_PMRC_91), S2_751–756. https://doi.org/10.3379/jmsjmag.15.s2_751

MLA 9

Suzuki, Atsushi, et al. “CHARACTERIZATION OF DIAMOND-LIKE CARBON THIN FILMS DEPOSITED BY FACING TARGETS SPUTTERING OF GLASS-LIKE CARBON.” Journal of the Magnetics Society of Japan, vol. 15, no. S_2_PMRC_91, 1991, pp. S2_751–756. https://doi.org/10.3379/jmsjmag.15.s2_751.

Chicago

Suzuki, Atsushi, Y. Hoshi, Tsutomu Isobe, and Jack H. JUDY. 1991. “CHARACTERIZATION OF DIAMOND-LIKE CARBON THIN FILMS DEPOSITED BY FACING TARGETS SPUTTERING OF GLASS-LIKE CARBON.” Journal of the Magnetics Society of Japan 15 (S_2_PMRC_91): S2_751–756. https://doi.org/10.3379/jmsjmag.15.s2_751.

Harvard

Suzuki, A. et al. (1991) ‘CHARACTERIZATION OF DIAMOND-LIKE CARBON THIN FILMS DEPOSITED BY FACING TARGETS SPUTTERING OF GLASS-LIKE CARBON’, Journal of the Magnetics Society of Japan, 15(S_2_PMRC_91), pp. S2_751–756. doi:10.3379/jmsjmag.15.s2_751.

IEEE

A. Suzuki, Y. Hoshi, T. Isobe, and J. H. JUDY, “CHARACTERIZATION OF DIAMOND-LIKE CARBON THIN FILMS DEPOSITED BY FACING TARGETS SPUTTERING OF GLASS-LIKE CARBON,” Journal of the Magnetics Society of Japan, vol. 15, no. S_2_PMRC_91, pp. S2_751–756, 1991, doi: 10.3379/jmsjmag.15.s2_751.

BibTeX

@article{suzuki1991characterization,
  title     = {{CHARACTERIZATION OF DIAMOND-LIKE CARBON THIN FILMS DEPOSITED BY FACING TARGETS SPUTTERING OF GLASS-LIKE CARBON}},
  author    = {Suzuki, Atsushi and Hoshi, Y. and Isobe, Tsutomu and JUDY, Jack H.},
  journal   = {Journal of the Magnetics Society of Japan},
  year      = {1991},
  volume    = {15},
  number    = {S_2_PMRC_91},
  pages     = {S2_751--756},
  doi       = {10.3379/jmsjmag.15.s2_751},
  url       = {https://doi.org/10.3379/jmsjmag.15.s2_751}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • diamond-like carbon films
  • facing targets sputtering
  • argon pressure
  • optical properties
  • Raman spectroscopy
  • electrical resistivity
  • microhardness
  • friction coefficient

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Suzuki, A., Hoshi, Y., Isobe, T., & JUDY, J. H. (1991). CHARACTERIZATION OF DIAMOND-LIKE CARBON THIN FILMS DEPOSITED BY FACING TARGETS SPUTTERING OF GLASS-LIKE CARBON. Journal of the Magnetics Society of Japan, 15(S_2_PMRC_91), S2_751–756. https://doi.org/10.3379/jmsjmag.15.s2_751

How many times has this paper been cited?

1 times, according to OpenAlex on 16 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access: read the free full text at Journal of the Magnetics Society of Japan.

Who wrote this paper?

Atsushi Suzuki, Y. Hoshi, Tsutomu Isobe, Jack H. JUDY.

What is the DOI of this paper?

10.3379/jmsjmag.15.s2_751. The permanent link is https://doi.org/10.3379/jmsjmag.15.s2_751.

Bibliographic data from OpenAlex (CC0), last checked 16 November 2026. ResearchGuru does not host this paper; the links go to the publisher or the repository that does.