Journal article · 2024 · Open access

Characterization of 3D printed composite for final dental restorations

Lucas Eigi Borges Tanaka, Camila da Silva Rodrigues, Manassés Tercio Vieira Grangeiro, Tiago Moreira Bastos Campos, Renata Marques de Melo

Clinical Oral Investigations, 28(11), 617 · Published 31 October 2024 · DOI 10.1007/s00784-024-06003-8

Open full textView at the publisherCite this paper

In brief

“Characterization of 3D printed composite for final dental restorations” is a 2024 journal article by Lucas Eigi Borges Tanaka and 4 co-authors, published in Clinical Oral Investigations. OpenAlex counts 18 citations as of 18 November 2026, which puts it in the top 2% of works published in 2024 by citations. It is open access under a CC BY licence: the full text is free to read at Research Square.

Citations
18
Most cited in
2025 (9)
Field-weighted impact
5.73
References
40
Authors
5

Abstract

Objectives This study evaluated the surface, mechanical properties, and optical behavior of a 3D printing resin comparing it with a machinable resin composite. Materials and Methods Specimens of different sizes and shapes were either printed (Vitality, Smart Dent) or machined (Grandio Blocs, Voco GmbH) resin composites with similar composition were prepared. Surface and mechanical characterization were performed with Knoop hardness, flexural strength (three-point-bending), elastic modulus tests. The wear of the tested materials was evaluated against steatite antagonists. The optical properties stability (color change, ΔE00, and translucency, TP00) were observed after staining in red wine. In addition, the bond strength of the resin composites to two resin cement protocols were investigated with microshear bond strength tests at baseline and after thermocycling. Scanning electron microscope (SEM) coupled with Energy-Dispersive X-ray Spectroscopy (EDS) was used for microstructural and chemical characterization. Statistical analyses were performed with t- and ANOVA tests. Results Hardness values (132.76 (16.32) KH- Grandio and 35.87 (2.78) KH - printed), flexural strength (172.17 (26.99) MPa - Grandio and 88.69 (8.39) MPa - printed) and color/translucency change of 1.86 (0.31)/0.06 - Grandio and 3.73 (0.36)/9, 16- printed and depth of wear (24.97 mm (3.60)- Grandio and 7.16 mm (2.84) - printed) were statistically different. No statistical differences were observed for mean roughness (Ra) between materials. For bond strength, mean values (MPa) for non-aged and aged groups were respectively 21.76 (6.64) / 31.9 (12.66) for Bifix cement (Voco GmbH, Cuxhaven, Germany) and 26.75 (5.14) / 24.36 (6.85) for Variolink cement (Ivoclar Vivadent, Schaan, Liechtenstein) in Vitality and 17.79 (3.89) / 9.01 (3.36) ) for Bifix cement and 22.09 (6.55) / 11.01 (3.77) for Variolink cement in Grandio. The material (p < 0.001) and aging (p < 0.003) factor did affect bond strength but the cement factor did not (p = 0.202). No statistical differences were observed for mean roughness (Ra) between materials. The better dispersion and larger size of the inorganic particles in the Grandio were contrasted with the clustered smaller particles of Vitality, under SEM. Results The mechanical properties and color stability of the machinable resin were superior to those of the printed resin, probably due to the greater amount and dispersion of inorganic particles in the machinable resin, but bond strength after aging was stronger and more stable in the printed resin. Clinical Relevance: This study aims to evaluate the possibility of the use of printed composite resin restorations, which can serve as a reference to corroborate its use or to indicate where the manufacture of printed restorations should be improved…

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Tanaka, L. E. B., Rodrigues, C. D. S., Grangeiro, M. T. V., Campos, T. M. B., & de Melo, R. M. (2024). Characterization of 3D printed composite for final dental restorations. Clinical Oral Investigations, 28(11), 617. https://doi.org/10.1007/s00784-024-06003-8

MLA 9

Tanaka, Lucas Eigi Borges, et al. “Characterization of 3D printed composite for final dental restorations.” Clinical Oral Investigations, vol. 28, no. 11, 2024, p. 617. https://doi.org/10.1007/s00784-024-06003-8.

Chicago

Tanaka, Lucas Eigi Borges, Camila da Silva Rodrigues, Manassés Tercio Vieira Grangeiro, Tiago Moreira Bastos Campos, and Renata Marques de Melo. 2024. “Characterization of 3D printed composite for final dental restorations.” Clinical Oral Investigations 28 (11): 617. https://doi.org/10.1007/s00784-024-06003-8.

Harvard

Tanaka, L. E. B. et al. (2024) ‘Characterization of 3D printed composite for final dental restorations’, Clinical Oral Investigations, 28(11), p. 617. doi:10.1007/s00784-024-06003-8.

IEEE

L. E. B. Tanaka, C. D. S. Rodrigues, M. T. V. Grangeiro, T. M. B. Campos, and R. M. de Melo, “Characterization of 3D printed composite for final dental restorations,” Clinical Oral Investigations, vol. 28, no. 11, p. 617, 2024, doi: 10.1007/s00784-024-06003-8.

BibTeX

@article{tanaka2024characterization,
  title     = {{Characterization of 3D printed composite for final dental restorations}},
  author    = {Tanaka, Lucas Eigi Borges and Rodrigues, Camila da Silva and Grangeiro, Manassés Tercio Vieira and Campos, Tiago Moreira Bastos and de Melo, Renata Marques},
  journal   = {Clinical Oral Investigations},
  year      = {2024},
  volume    = {28},
  number    = {11},
  pages     = {617},
  doi       = {10.1007/s00784-024-06003-8},
  url       = {https://doi.org/10.1007/s00784-024-06003-8}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Health Sciences › Dentistry › General Dentistry › Dental materials and restorations

  • dental restorations
  • flexural strength
  • Knoop hardness
  • elastic modulus
  • wear resistance
  • color stability
  • translucency
  • microshear bond strength

Work with this paper

Most-cited papers in Dentistry

All highly cited Dentistry papers

Questions about this paper

How do I cite this paper in APA style?

Tanaka, L. E. B., Rodrigues, C. D. S., Grangeiro, M. T. V., Campos, T. M. B., & de Melo, R. M. (2024). Characterization of 3D printed composite for final dental restorations. Clinical Oral Investigations, 28(11), 617. https://doi.org/10.1007/s00784-024-06003-8

How many times has this paper been cited?

18 times, according to OpenAlex on 18 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Research Square: sign in and open the full text from this page.

Who wrote this paper?

Lucas Eigi Borges Tanaka, Camila da Silva Rodrigues, Manassés Tercio Vieira Grangeiro, Tiago Moreira Bastos Campos, Renata Marques de Melo.

What is the DOI of this paper?

10.1007/s00784-024-06003-8, permanently at https://doi.org/10.1007/s00784-024-06003-8. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 18 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.