Conference paper · 2017 · Open access

CFD modelling and performance increase of a pusher type reheating furnace using oxy-fuel burners

Bernhard Mayr, René Prieler, Martin Demuth, Luca Moderer, Christoph Hochenauer

Energy Procedia, 120, 462–468 · Published 1 August 2017 · DOI 10.1016/j.egypro.2017.07.222

Open PDFView at the publisherCite this paper

In brief

“CFD modelling and performance increase of a pusher type reheating furnace using oxy-fuel burners” is a 2017 conference paper by Bernhard Mayr and 4 co-authors, published in Energy Procedia. OpenAlex counts 44 citations as of 22 November 2026, which puts it in the top 8% of works published in 2017 by citations. It is open access under a CC BY-NC-ND licence: the full text is free to read at Energy Procedia.

Citations
44
Most cited in
2019 (8)
Field-weighted impact
11.51
References
12
Authors
5

Abstract

In conventional combustion systems which use air as oxidizer, a huge amount of the heat of formation is absorbed by the nitrogen in the air. In oxygen enriched or oxy-fuel combustion an O 2 /N 2 -mixture with a higher concentration of oxygen is used. Due to the lower amount of nitrogen in the oxidizer the flame temperature increases and radiative heat transfer is improved in the furnace. Therefore, the influence of additional oxy-fuel jet burners on the productivity of a pusher type reheating furnace is investigated in this paper. Due to the special arrangement of the billet in this type of furnace the billets can be treated as a fluid with a very high viscosity. Therefore, the periodic transient reheating of the billets and the gas phase combustion was calculated in one steady state calculation. The combustion in the gas phase is described by the steady laminar flamelet approach for air-fuel combustion and the eddy dissipation concept model is used in the simulation with the oxy-fuel burners. The results of the gas phase simulation with air as oxidizer was validated with measurements and showed an average deviation of 38 K. The calculated billet temperature was also compared to the measurements and showed deviation of 27 K which can be seen as a good agreement. With this model the influence of additional oxy-fuel burners is investigated. The investigation showed that with additional oxy-fuel burners the productivity of the furnace can be increased from 60 t/h to 68 t/h and furthermore the furnace efficiency increases from 62.9% to 65%. This shows the beneficial effect of using oxy-fuel combustion.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Mayr, B., Prieler, R., Demuth, M., Moderer, L., & Hochenauer, C. (2017). CFD modelling and performance increase of a pusher type reheating furnace using oxy-fuel burners. Energy Procedia, 120, 462–468. https://doi.org/10.1016/j.egypro.2017.07.222

MLA 9

Mayr, Bernhard, et al. “CFD modelling and performance increase of a pusher type reheating furnace using oxy-fuel burners.” Energy Procedia, vol. 120, 2017, pp. 462–468. https://doi.org/10.1016/j.egypro.2017.07.222.

Chicago

Mayr, Bernhard, René Prieler, Martin Demuth, Luca Moderer, and Christoph Hochenauer. 2017. “CFD modelling and performance increase of a pusher type reheating furnace using oxy-fuel burners.” Energy Procedia 120: 462–468. https://doi.org/10.1016/j.egypro.2017.07.222.

Harvard

Mayr, B. et al. (2017) ‘CFD modelling and performance increase of a pusher type reheating furnace using oxy-fuel burners’, Energy Procedia, 120, pp. 462–468. doi:10.1016/j.egypro.2017.07.222.

IEEE

B. Mayr, R. Prieler, M. Demuth, L. Moderer, and C. Hochenauer, “CFD modelling and performance increase of a pusher type reheating furnace using oxy-fuel burners,” Energy Procedia, vol. 120, pp. 462–468, 2017, doi: 10.1016/j.egypro.2017.07.222.

BibTeX

@inproceedings{mayr2017modelling,
  title     = {{CFD modelling and performance increase of a pusher type reheating furnace using oxy-fuel burners}},
  author    = {Mayr, Bernhard and Prieler, René and Demuth, Martin and Moderer, Luca and Hochenauer, Christoph},
  booktitle = {Energy Procedia},
  year      = {2017},
  volume    = {120},
  pages     = {462--468},
  doi       = {10.1016/j.egypro.2017.07.222},
  url       = {https://doi.org/10.1016/j.egypro.2017.07.222}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201822
201988
202077
202166
202222
202355
202477
202555
202622

Its field-weighted citation impact is 11.51: it has been cited 11.51 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Computational Mechanics › Combustion and flame dynamics

  • oxy-fuel combustion
  • reheating furnace
  • oxy-fuel burners
  • flamelet model
  • eddy dissipation model
  • furnace productivity
  • furnace efficiency
  • radiative transfer

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Mayr, B., Prieler, R., Demuth, M., Moderer, L., & Hochenauer, C. (2017). CFD modelling and performance increase of a pusher type reheating furnace using oxy-fuel burners. Energy Procedia, 120, 462–468. https://doi.org/10.1016/j.egypro.2017.07.222

How many times has this paper been cited?

44 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Energy Procedia: sign in and open the PDF from this page.

Who wrote this paper?

Bernhard Mayr, René Prieler, Martin Demuth, Luca Moderer, Christoph Hochenauer.

What is the DOI of this paper?

10.1016/j.egypro.2017.07.222, permanently at https://doi.org/10.1016/j.egypro.2017.07.222. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.