Journal article · 2024 · Open access
Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel
Coatings, 14(12), 1491 · Published 27 November 2024 · DOI 10.3390/coatings14121491
In brief
“Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel” is a 2024 journal article by Gustavo M. Minquiz and 8 co-authors, published in Coatings. OpenAlex counts 7 citations as of 17 November 2026, which puts it in the top 4% of works published in 2024 by citations. It is open access under a CC BY licence: the full text is free to read at Coatings.
- Citations
- 7
- Most cited in
- 2025 (4)
- Field-weighted impact
- 0.89
- References
- 39
- Authors
- 9
Abstract
Tool selection is relevant because a wide variety of materials exhibit different machinability behaviors. Tool life during manufacturing is commonly associated with productivity. Insert developers have been using coatings on cutting tools to enhance their performance, with chemical vapor deposition (CVD) and physical vapor deposition (PVD) being the two most used techniques. This study analyzed the cutting tool wear mechanism by machining AISI D2 steel using two different inserts of TiAlN/TiN PVD and TiCN/Al2O3 CVD as layers deposited on a carbide substrate. The two inserts were tested at three different cutting speeds, namely, low, medium, and high; these values were below the data suggested by the supplier catalog. The flank wear and rake face were analyzed using scanning electron microscopy (SEM) and energy-dispersive X-ray spectrometry (EDX). The adhesion material, edge deformation, and abrasion were the main wear mechanisms before catastrophic damage occurred at the three different cutting speeds in the PVD cutting tool. Nevertheless, increasing the cutting speed reduced the tool life from 84% to 61% at high values compared to the medium values of PVD and CVD, respectively, where the medium value resulted in a balance between the material removal rate and tool life. The wear mechanism of the CVD tool was BUE and chipping; nevertheless, its craters were larger than those of the PVD. Compared to those configured for PVD, the CVD insert demonstrated the ability to machine D2 steel at twice the cutting speed with a workpiece surface roughness of 0.3 µm, in contrast to a variation of 0.6 to 0.15 µm with the PVD tool.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Minquiz, G. M., González-Sierra, N. E., Méndez, J. F., Reyes, A. C. P., Moreno, M., Morales-Sánchez, A., López, J. A. L., Simón, Z. J. H., & Denicia-Carral, C. (2024). Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel. Coatings, 14(12), 1491. https://doi.org/10.3390/coatings14121491
MLA 9
Minquiz, Gustavo M., et al. “Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel.” Coatings, vol. 14, no. 12, 2024, p. 1491. https://doi.org/10.3390/coatings14121491.
Chicago
Minquiz, Gustavo M., N. E. González-Sierra, Javier Flores Méndez, Ana Cecilia Piñón Reyes, Mario Moreno, Alfredo Morales-Sánchez, José Alberto Luna López, Zaira Jocelyn Hernández Simón, and Claudia Denicia-Carral. 2024. “Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel.” Coatings 14 (12): 1491. https://doi.org/10.3390/coatings14121491.
Harvard
Minquiz, G. M. et al. (2024) ‘Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel’, Coatings, 14(12), p. 1491. doi:10.3390/coatings14121491.
IEEE
G. M. Minquiz et al., “Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel,” Coatings, vol. 14, no. 12, p. 1491, 2024, doi: 10.3390/coatings14121491.
BibTeX
@article{minquiz2024analysis,
title = {{Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel}},
author = {Minquiz, Gustavo M. and González-Sierra, N. E. and Méndez, Javier Flores and Reyes, Ana Cecilia Piñón and Moreno, Mario and Morales-Sánchez, Alfredo and López, José Alberto Luna and Simón, Zaira Jocelyn Hernández and Denicia-Carral, Claudia},
journal = {Coatings},
year = {2024},
volume = {14},
number = {12},
pages = {1491},
doi = {10.3390/coatings14121491},
url = {https://doi.org/10.3390/coatings14121491}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Topic and keywords
Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- AISI D2 tool steel
- carbide inserts
- flank wear
- cutting speed
- tool life
- edge deformation
- adhesion
- crater formation
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Minquiz, G. M., González-Sierra, N. E., Méndez, J. F., Reyes, A. C. P., Moreno, M., Morales-Sánchez, A., López, J. A. L., Simón, Z. J. H., & Denicia-Carral, C. (2024). Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel. Coatings, 14(12), 1491. https://doi.org/10.3390/coatings14121491
How many times has this paper been cited?
7 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Coatings: sign in and open the full text from this page.
Who wrote this paper?
Gustavo M. Minquiz, N. E. González-Sierra, Javier Flores Méndez, Ana Cecilia Piñón Reyes, Mario Moreno, Alfredo Morales-Sánchez, José Alberto Luna López, Zaira Jocelyn Hernández Simón, Claudia Denicia-Carral.
What is the DOI of this paper?
10.3390/coatings14121491, permanently at https://doi.org/10.3390/coatings14121491. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.