Dissertation · 1999 · Open access

A New Mechanical Characterization Method for Thin Film Microactuators and Its Application to NiTiCu Shape Memory Alloy

Kirk P. Seward

DSpace@MIT (Massachusetts Institute of Technology) · Published 1 January 1999

Open full textCite this paper

In brief

“A New Mechanical Characterization Method for Thin Film Microactuators and Its Application to NiTiCu Shape Memory Alloy” is a 1999 dissertation by Kirk P. Seward, published in DSpace@MIT (Massachusetts Institute of Technology). OpenAlex counts 1 citations as of 22 November 2026. It is open access under a CC BY-NC licence: the full text is free to read at DSpace@MIT (Massachusetts Institute of Technology).

Citations
1
Most cited in
2020 (1)
Authors
1

Abstract

In an effort to develop a more full characterization tool of shape memory alloys, a new technique is presented for the mechanical characterization of microactuators and applied to SMA thin films. A test instrument was designed to utilize a spring-loaded transducer in measuring displacements with resolution of 1.5 pm and forces with resolution of 0.2 mN. Employing an out-of-plane loading method for freestanding SMA thin films, strain resolution of 30{mu}{epsilon} and stress resolution of 2.5 MPa were achieved. This new testing method is presented against previous SMA characterization methods for purposes of comparison. Four mm long, 2 {micro}m thick NiTiCu ligaments suspended across open windows were bulk micromachined for use in the out-of-plane stress and strain measurements. The fabrication process used to micromachine the ligaments is presented step-by-step, alongside methods of fabrication that failed to produce testable ligaments. Static analysis showed that 63% of the applied strain was recovered while ligaments were subjected to tensile stresses of 870 MPa. In terms of recoverable stress and recoverable strain, the ligaments achieved maximum recovery of 700 MPa and 3.0% strain. No permanent deformations were seen in any ligament during deflection measurements. Maximum actuation forces and displacements produced by the 4 mm ligaments situated on 1 cm square test chips were 56 mN and 300 {micro}m, respectively. Fatigue analysis of the ligaments showed degradation in recoverable strain from 0.33% to 0.24% with 200,000 cycles, corresponding to deflections of 90 {micro}m and forces of 25 mN. Cycling also produced a wavering shape memory effect late in ligament life, leading to broad inconsistencies of as much as 35% deviation from average. Unexpected phenomena like stress-induced martensitic twinning that leads to less recoverable stress and the shape memory behavior of long life devices are addressed. Finally, a model for design of microactuators using shape memory alloys is presented to illustrate how results obtained from these tests can be interpreted and applied to the creation of MEMS devices.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Seward, K. P. (1999). A New Mechanical Characterization Method for Thin Film Microactuators and Its Application to NiTiCu Shape Memory Alloy. DSpace@MIT (Massachusetts Institute of Technology). http://hdl.handle.net/1721.1/9425

MLA 9

Seward, Kirk P. “A New Mechanical Characterization Method for Thin Film Microactuators and Its Application to NiTiCu Shape Memory Alloy.” DSpace@MIT (Massachusetts Institute of Technology), 1999. http://hdl.handle.net/1721.1/9425.

Chicago

Seward, Kirk P. 1999. “A New Mechanical Characterization Method for Thin Film Microactuators and Its Application to NiTiCu Shape Memory Alloy.” DSpace@MIT (Massachusetts Institute of Technology). http://hdl.handle.net/1721.1/9425.

Harvard

Seward, K. P. (1999) ‘A New Mechanical Characterization Method for Thin Film Microactuators and Its Application to NiTiCu Shape Memory Alloy’, DSpace@MIT (Massachusetts Institute of Technology). Available at: http://hdl.handle.net/1721.1/9425.

IEEE

K. P. Seward, “A New Mechanical Characterization Method for Thin Film Microactuators and Its Application to NiTiCu Shape Memory Alloy,” DSpace@MIT (Massachusetts Institute of Technology), 1999.

BibTeX

@phdthesis{seward1999mechanical,
  title     = {{A New Mechanical Characterization Method for Thin Film Microactuators and Its Application to NiTiCu Shape Memory Alloy}},
  author    = {Seward, Kirk P.},
  year      = {1999},
  url       = {http://hdl.handle.net/1721.1/9425}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Materials Science › Materials Chemistry › Shape Memory Alloy Transformations

  • shape memory alloys
  • mechanical characterization
  • out-of-plane loading
  • bulk micromachining
  • recoverable strain
  • fatigue (material)
  • MEMS design

Work with this paper

Most-cited papers in Materials Science

All highly cited Materials Science papers

Questions about this paper

How do I cite this paper in APA style?

Seward, K. P. (1999). A New Mechanical Characterization Method for Thin Film Microactuators and Its Application to NiTiCu Shape Memory Alloy. DSpace@MIT (Massachusetts Institute of Technology). http://hdl.handle.net/1721.1/9425

How many times has this paper been cited?

1 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at DSpace@MIT (Massachusetts Institute of Technology): sign in and open the full text from this page.

Who wrote this paper?

Kirk P. Seward.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.