Journal article · 2021 · Open access

A 3D-Printable Robotic Gripper Based on Thick Panel Origami

Chenying Liu, Perla Maiolino, Zhong You

Frontiers in Robotics and AI, 8, 730227 · Published 8 September 2021 · DOI 10.3389/frobt.2021.730227

Open PDFView at the publisherCite this paper

In brief

“A 3D-Printable Robotic Gripper Based on Thick Panel Origami” is a 2021 journal article by Chenying Liu and 2 co-authors, published in Frontiers in Robotics and AI. OpenAlex counts 30 citations as of 22 November 2026, which puts it in the top 6% of works published in 2021 by citations. It is open access under a CC BY licence: the full text is free to read at Frontiers in Robotics and AI.

Citations
30
Most cited in
2025 (10)
Field-weighted impact
0.97
References
21
Authors
3

Abstract

Origami has been a source of inspiration for the design of robots because it can be easily produced using 2D materials and its motions can be well quantified. However, most applications to date have utilised origami patterns for thin sheet materials with a negligible thickness. If the thickness of the material cannot be neglected, commonly known as the thick panel origami, the creases need to be redesigned. One approach is to place creases either on top or bottom surfaces of a sheet of finite thickness. As a result, spherical linkages in the zero-thickness origami are replaced by spatial linkages in the thick panel one, leading to a reduction in the overall degrees of freedom (DOFs). For instance, a waterbomb pattern for a zero-thickness sheet shows multiple DOFs while its thick panel counterpart has only one DOF, which significantly reduces the complexity of motion control. In this article, we present a robotic gripper derived from a unit that is based on the thick panel six-crease waterbomb origami. Four such units complete the gripper. Kinematically, each unit is a plane-symmetric Bricard linkage, and the gripper can be modelled as an assembly of Bricard linkages, giving it single mobility. A gripper prototype was made using 3D printing technology, and its motion was controlled by a set of tendons tied to a single motor. Detailed kinematic modelling was done, and experiments were carried out to characterise the gripper's behaviours. The positions of the tips on the gripper, the actuation force on tendons, and the grasping force generated on objects were analysed and measured. The experimental results matched well with the analytical ones, and the repeated tests demonstrate that the concept is viable. Furthermore, we observed that the gripper was also capable of grasping non-symmetrical objects, and such performance is discussed in detail in the paper.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Liu, C., Maiolino, P., & You, Z. (2021). A 3D-Printable Robotic Gripper Based on Thick Panel Origami. Frontiers in Robotics and AI, 8, 730227. https://doi.org/10.3389/frobt.2021.730227

MLA 9

Liu, Chenying, et al. “A 3D-Printable Robotic Gripper Based on Thick Panel Origami.” Frontiers in Robotics and AI, vol. 8, 2021, p. 730227. https://doi.org/10.3389/frobt.2021.730227.

Chicago

Liu, Chenying, Perla Maiolino, and Zhong You. 2021. “A 3D-Printable Robotic Gripper Based on Thick Panel Origami.” Frontiers in Robotics and AI 8: 730227. https://doi.org/10.3389/frobt.2021.730227.

Harvard

Liu, C., Maiolino, P. and You, Z. (2021) ‘A 3D-Printable Robotic Gripper Based on Thick Panel Origami’, Frontiers in Robotics and AI, 8, p. 730227. doi:10.3389/frobt.2021.730227.

IEEE

C. Liu, P. Maiolino, and Z. You, “A 3D-Printable Robotic Gripper Based on Thick Panel Origami,” Frontiers in Robotics and AI, vol. 8, p. 730227, 2021, doi: 10.3389/frobt.2021.730227.

BibTeX

@article{liu2021printable,
  title     = {{A 3D-Printable Robotic Gripper Based on Thick Panel Origami}},
  author    = {Liu, Chenying and Maiolino, Perla and You, Zhong},
  journal   = {Frontiers in Robotics and AI},
  year      = {2021},
  volume    = {8},
  pages     = {730227},
  doi       = {10.3389/frobt.2021.730227},
  url       = {https://doi.org/10.3389/frobt.2021.730227}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
202233
202333
202455
20251010
202699

Its field-weighted citation impact is 0.97: it has been cited 0.97 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Control and Systems Engineering › Robotic Mechanisms and Dynamics

  • robotic gripper
  • origami-inspired robotics
  • tendon-driven actuation
  • single-degree-of-freedom mechanisms
  • 3D printing
  • grasping force
  • kinematic modelling

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Liu, C., Maiolino, P., & You, Z. (2021). A 3D-Printable Robotic Gripper Based on Thick Panel Origami. Frontiers in Robotics and AI, 8, 730227. https://doi.org/10.3389/frobt.2021.730227

How many times has this paper been cited?

30 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Frontiers in Robotics and AI: sign in and open the PDF from this page.

Who wrote this paper?

Chenying Liu, Perla Maiolino, Zhong You.

What is the DOI of this paper?

10.3389/frobt.2021.730227, permanently at https://doi.org/10.3389/frobt.2021.730227. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.